[24-hour hotline: 13809488488] Guizhou Road Lyle Floor Engineering Co. Kerry floor paint, epoxy Carey, Carey epoxy floor paint, epoxy floor Kerry, Ring of Kerry epoxy floor paint, floor paint parking Carey, Carey anti-static floor paint, epoxy floor paint industrial plants Carey, Carey thin coating of mortar floor, Carey anti-static floor paint; Kerry Ring Oxygen floor paint will be the most sophisticated technology, the most favorable price to provide you with the most thoughtful Carey floor paint, epoxy Carey, Carey epoxy floor paint, epoxy floor Carey, Carey epoxy floor paint, floor paint parking Carey, Carey anti-static epoxy floor paint, epoxy floor paint industrial plants Carey, Carey thin coating of mortar flooring, anti-static floor Carey Paint Service! Welcome to your call. 4 construction steps (1) primer construction: the low-viscosity solvent-free epoxy sealer with a good, roll coating, knife or brush, to make it fully wet concrete and penetrate into the concrete lining. (2) Tu construction: more crucial in the coating construction, epoxy paste, curing agent and the amount of quartz sand mix Trail mix stir (sometimes ripening), with a trowel into a certain thickness of the flat dense Layer (recommended serrated trowel, then use a roller to roll with nails release membrane air), also can be smooth trowel, plus a number of larger amount of sand; also uses scratch, plus a greater amount of sand. After curing the coating, blade putty filled and polished smooth, provide a good surface for the topcoat. (3) putty repair: to exist on the surface layer of cement pits filled using EPOXY mortar repair, nature conservation dry polished smooth. (4) Construction of topcoat: The epoxy hardener paste and mixed uniformly, and trowel, brush, roller or spray, to self-leveling, to obtain a flat uniform surface coating. (5) Acceptance of construction: surface smooth and clean, consistent color, no color. (6) Note: Avoid at low temperature and high humidity conditions of construction;-component mixture should be used up as soon as possible using the period; After the painting is completed, the maintenance should be sufficient to put to use; should be based on the substrate flatness conditions and requirements, to determine the coating thickness. Surface flatness worse, should be thicker coating system, the greater the load the coating, the coating should be as thick as the coating is too thin, easily damaged during use. Fifth, self-leveling epoxy floor quality assessment Currently there are many self-leveling coatings manufacturers and construction engineering company, but the quality difference in the final self-leveling flooring is obvious, according to the author for many years in this study can be used as flooring customers and end-users evaluate Project case by reference: 1, surface conditions: As a self-leveling highly decorative surface coatings, requires a good level of self-leveling, but should not have debris and other adverse conditions. 2, plumpness: In the past, many domestic manufacturers are basically self-leveling without this technical indicators, but in Japan and other countries is a basic technical indicators, we usually use an index to measure the reflectance plumpness, we require good at curing reflectance on leveling the ground to reach 95%, and we are currently many domestic manufacturers of products for testing showed that the reflection rate of less than 85%, resulting in brightness is not high, it is the technical guidelines mentioned above Differences due. 3, hardness: as flooring, floor surface after curing requires a certain degree of hardness, so as to achieve sufficient abrasion resistance, self-leveling coatings filler will sink in the ground floor of the cured hardness is not too high, the general requirements floor hardness> 2H, in order to achieve industrial requirements. Epoxy-based surface treatment quality control carried out prior to coating the substrate base surface treatment is very important, related to the floor coating durability. Base surface treatment has the following purpose and role. 1, to make up for lack of proper treatment by defective substrates; 2, removal of impurities in the substrate surface coated with dirt; 3, enhance the adhesion of the coating and the substrate; 4 for coating floor paint to create a smoother, more surface, in order to save the amount of paint. Different substrates need to take a different approach, usually takes epoxy coating substrates have a new concrete floor cement mortar, old paint or oil ground, terrazzo floors, marble or granite floors, steel platform or the like. Guizhou Road Lyle Floor Engineering Co., Ltd. Contact: Mr. Lin Tel: 13809488488 Tel :0851-2228236 QQ: 379852519 official website: www.daolaier.com